Skip to content

Add Corning 3337 24-well plate labware - #61

Draft
kingbedjed wants to merge 2 commits into
mainfrom
labware/corning-3337
Draft

kingbedjed wants to merge 2 commits into
mainfrom
labware/corning-3337

Conversation

@kingbedjed

Copy link
Copy Markdown
Contributor

The request

Slack user U0APRMP9RH8 in #labware-requests, 2026-11-13 (permalink):

corning costar 24 well plate Cat no: 3337

Closes #60

Decisions needed

  • A separate entry for the same mould. 3337 is the CellBIND item in a mould Corning also sells as 3524/3527 (TC-treated), 3526 (non-treated) and 3473 (ultra-low attachment). Corning_costar_24_well_plate.json (3524) and Corning_3527_24_well_plate.json are already in the registry with the same footprint, pitch and A1 offsets. This pull request adds 3337 as its own entry so it can be found by its catalogue number, as 3527 was added beside 3524 (and as Add Corning 3336 12-well plate labware #59 does for the 12-well CellBIND 3336). The alternative is to close this and point the requester at 3524.
  • Working volume. The product page gives a "Recommended Medium Well Volume" of 0.38–0.57 mL, recorded here as working_volume_min / working_volume_max. The Product Description gives one "working volume per well", 2 mL, which the existing 3524 entry quotes. Say if the 2 mL should be used instead.
  • Is the plate in hand really 3337 (CellBIND)? The request says "costar 24 well", which matches. The geometry is the same for 3524/3526/3527/3473 either way.

What is included

file plate pitch grid A1 (left, top) well bottom / top depth bottom
Corning_3337_24_well_plate.json Corning Costar CellBIND 3337 24 well 19.304 mm 4 x 6 17.48 / 13.77 mm 15.62 / 16.26 mm 17.40 mm clear polystyrene, 1.27 mm thick, underside 2.54 mm up

Plus one row in tests/test_labware.py.

Figures

rendered from the JSON on this branch Corning drawing DWG01261 Rev B, page 1
Corning 3337 as the JSON describes it Corning drawing DWG01261 Rev B, page 1

Corning's catalogue photo for 3337, from the product page:

Corning catalogue photo for 3337

Sources used

  • Corning customer drawing DWG01261 Rev B (6/22/18), "24 well plate and cover": the controlling document. It carries no catalogue number and is the mould drawing for the Costar 24-well family. It is vector with no text layer, so it was read from renders. It prints the footprint, both heights, pitch, A1 offsets, opening diameter, depth, bottom thickness and bottom elevation.
  • Product Description 3337, rev 9 (2 Feb 2026, PDF): confirms 3337 is the CellBIND Costar 24-well. It agrees with the drawing and gives the bottom diameter, 0.615 in (15.62 mm).
  • Corning family sheet "Microplate Dimensions for Corning Cell Culture Microplates" (1/16/2019, now only on the Internet Archive, marked "Corning Restricted", so it is linked and not attached): lists 3337, 3524, 3526, 3527 and 3473 on one row (same mould). It also prints the 15.62 mm bottom diameter and is the only source for the 13.74 mm skirt height.
  • Trap: www.corning.com returns 403 to plain curl. The drawing and the photo needed the full browser header set.

Judgement calls

  • diameter is the well bottom (15.62 mm, Product Description and family sheet) and diameter_top the opening (16.26 mm, printed at the rim on the drawing). The existing 3524 and 3527 entries predate this convention and have the opening in diameter. This pull request leaves them as they are.
  • The A1 offset is 1.86 mm right of centre along the plate's length (17.48 mm left margin, 13.76 mm right). That is printed on the drawing, visible in its plan view, and matches the family sheet (17.46). It is not a swapped axis.
  • floor_height 3.81 mm is derived, as 2.54 + 1.27. Corning's vertical numbers do not close: depth + bottom thickness + bottom elevation = 21.21 mm against the printed 20.27 mm plate height. That is the same 0.94 mm gap as on the 6- and 12-well sheets. Each value is recorded as printed.
  • skirt_height 13.74 mm is from the family sheet. The drawing's side view draws the step lower (about 11.1 mm), but that view's vertical scale does not close against its own printed 22.63 mm, so nothing was scaled off it.
  • upper_outline is scaled off DWG01261 Rev B, assumed to scale. The top view draws the plate body inside the skirt, inset 1.89 mm (left) and 1.84 mm (top, right, bottom). The side view gives 1.78 / 1.70 mm at the two ends. The two corners at the column-6 end are rounded with r ≈ 12.0 mm, and the A1-end corners are square to within the drawn line. Calibration came from the printed 127.76 × 85.47 mm footprint (17.971 / 17.983 px/mm on a 600 dpi render), checked against the printed A1–D1 distance of 57.91 mm (0.45 % apart) and the 19.304 mm pitch (0.3 %). The uncertainty is about ±0.5 mm on the radius and ±0.15 mm on the insets.
  • The skirt outline is the drawing's outer line, a rectangle with corners of about 3 mm radius, so it is left to the standard. Skirt thickness is not drawn.

Testing

  • pytest -q: 192 passed.
  • lint (ruff check, ruff format --check, ty check at CI's pins via pixi): all passed.
  • Geometry check:
Corning_3337_24_well_plate.json
  name            'Corning Costar CellBIND 3337 24 well'   part '3337'
  footprint       127.760 mm x 85.470 mm x 20.270 mm
  grid            4 rows x 6 cols, pitch 19.304 mm
  well            circle, 16.260 mm at the top, 15.620 mm at the bottom, 17.400 mm deep, flat bottom
  A1 centre       17.480 mm from left, 13.770 mm from top
  far margins     13.760 mm right, 13.788 mm bottom
  centred A1      15.620 mm / 13.779 mm  (delta 1.860 mm / -0.009 mm)
  WARN  A1 is 1.860 mm off-centre in x; fine if the drawing says so, suspicious if the two offsets were swapped
  ok

The warning is expected: the drawing prints the off-centre grid (see Judgement calls).

🤖 Generated with Claude Code

Opened by the add-labware skill of ramona-claude 0.24.2 (ramona-llm ee2d4a6+dirty, prompt bc769991).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

This branch has not been deployed

No deployments
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment

Labels

None yet

Projects

None yet

Development

Successfully merging this pull request may close these issues.

Add Corning 3337 24-well plate to the labware registry

2 participants