PowerValue see it in MQTT Exporer but not under Devices - MQTT

[aavdberg]

Description

I have set the following:

ebusd --foreground --mqtthost=core-mosquitto --mqttport=1883 --mqttuser=*** --mqttpass=*** --scanconfig --mqttjson --configpath=/config/ebusd/en --accesslevel=* --mqttint=/etc/ebusd/mqtt-hassio.cfg --mqttvar=filter-direction=r|u|^w,filter-name=status|temp|yield|power|runtime|hours|starts|curve|^load$|^party$|sensor|pressure|press|mode|state|PowerValue|Temp|Water|SetMode|powervalue --mqtttopic=ebusd --device=ens:x.x.x.x:9999 --log=all:notice --log=bus:notice

and see the following in MQTT Explorer:

But in Devices - MQTT I don't see it.

Actual behavior

Dont see PowerValue in Devices - MQTT

Expected behavior

I expect to see the PowerValue in Devices - MQTT

ebusd version

26.1

ebusd arguments

ebusd --foreground --mqtthost=core-mosquitto --mqttport=1883 --mqttuser=**** --mqttpass=*** --scanconfig --mqttjson --configpath=/config/ebusd/en --accesslevel=* --mqttint=/etc/ebusd/mqtt-hassio.cfg --mqttvar=filter-direction=r|u|^w,filter-name=status|temp|yield|power|runtime|hours|starts|curve|^load$|^party$|sensor|pressure|press|mode|state|PowerValue|Temp|Water|SetMode|powervalue --mqtttopic=ebusd --device=ens:x.x.x.x:9999 --log=all:notice --log=bus:notice

Operating system

Debian 13 (Trixie) / Ubuntu 24-25 / Raspberry Pi OS 13

CPU architecture

x64

Dockerized

latest

Hardware interface

Adapter Shield v5/C6/Stick via USB

Related integration

MQTT Home Assistant via mqtt-hassio.cfg

Logs

2026-03-02 18:31:46.803 [device notice] transport opened
2026-03-02 18:31:46.805 [main notice] ebusd 26.1.26.1 started with broadcast scan on device: 10.20.26.64:9999, TCP, enhanced
2026-03-02 18:31:46.805 [bus notice] bus started with own address 31/36
2026-03-02 18:31:46.806 [device notice] reset, supports info
2026-03-02 18:31:46.809 [bus notice] signal acquired
2026-03-02 18:31:46.809 [device notice] extra info: firmware 1.1[6208].1[6208], jumpers 0x0b
2026-03-02 18:31:46.813 [mqtt notice] connection established
2026-03-02 18:31:56.806 [main notice] starting initial broadcast scan
2026-03-02 18:31:56.915 [update notice] sent write Broadcast Queryexistence QQ=31:
2026-03-02 18:32:21.969 [bus notice] new master 00, master count 2
2026-03-02 18:32:27.119 [main error] scan config 05: ERR: read timeout
2026-03-02 18:32:37.175 [bus notice] new master 03, master count 3
2026-03-02 18:32:39.335 [bus notice] scan 08: ;Vaillant;BAI00;0200;7503
2026-03-02 18:32:39.335 [update notice] store 08 ident: done
2026-03-02 18:32:39.335 [update notice] sent scan-read scan.08 QQ=31: Vaillant;BAI00;0200;7503
2026-03-02 18:32:39.335 [bus notice] scan 08: ;Vaillant;BAI00;0200;7503
2026-03-02 18:32:39.336 [main notice] read common config file vaillant/broadcast.csv
2026-03-02 18:32:39.336 [main notice] read common config file vaillant/general.csv
2026-03-02 18:32:39.336 [main notice] read common config file vaillant/scan.csv
2026-03-02 18:32:39.336 [main notice] read scan config file vaillant/08.bai.csv for ID "bai00", SW0200, HW7503
2026-03-02 18:32:39.508 [update notice] sent scan-read Scan.08 Id QQ=31:
2026-03-02 18:32:39.682 [update notice] sent scan-read Scan.08 Id QQ=31:
2026-03-02 18:32:39.853 [update notice] sent scan-read Scan.08 Id QQ=31:
2026-03-02 18:32:40.004 [bus notice] max. symbols per second: 107
2026-03-02 18:32:40.033 [update notice] sent scan-read Scan.08 Id QQ=31: 21;25;12;0010023673;3130;316592;N0
2026-03-02 18:32:40.037 [main notice] found messages: 236 (3 conditional on 35 conditions, 0 poll, 16 update)
2026-03-02 18:32:40.200 [update notice] sent scan-read Scan.08 Id QQ=31: 21;25;12;0010023673;3130;316592;N0
2026-03-02 18:32:40.368 [update notice] sent scan-read Scan.08 Id QQ=31: 21;25;12;0010023673;3130;316592;N0
2026-03-02 18:32:40.552 [update notice] sent scan-read Scan.08 Id QQ=31: 21;25;12;0010023673;3130;316592;N0
2026-03-02 18:32:40.729 [update notice] sent scan-read Scan.08 Id QQ=31: 21;25;12;0010023673;3130;316592;N0
2026-03-02 18:32:40.729 [bus notice] scan 08: ;21;25;12;0010023673;3130;316592;N0
2026-03-02 18:32:50.902 [update notice] sent poll-read bai CounterStartattempts1 QQ=31: 0
2026-03-02 18:32:56.182 [update notice] sent poll-read bai CounterStartattempts2 QQ=31: 0
2026-03-02 18:33:02.168 [update notice] sent poll-read bai CounterStartAttempts3 QQ=31: 0
2026-03-02 18:33:08.196 [update notice] sent poll-read bai CounterStartAttempts4 QQ=31: 0
2026-03-02 18:33:12.914 [main error] scan config 05: ERR: read timeout
2026-03-02 18:33:14.158 [update notice] sent poll-read bai DcfState QQ=31: nosignal
2026-03-02 18:33:14.916 [main notice] scan completed 1 time(s), check again
2026-03-02 18:33:20.159 [update notice] sent poll-read bai DeactivationsTemplimiter QQ=31: 0
2026-03-02 18:33:26.174 [update notice] sent poll-read bai DisplayMode QQ=31: 2
2026-03-02 18:33:32.186 [update notice] sent poll-read bai Expertlevel_ReturnTemp QQ=31: -1.81;cutoff
2026-03-02 18:33:38.184 [update error] unable to parse poll-read bai ExternalFlowTempDesired from 3108b509030d2500 / 00: ERR: invalid position
2026-03-02 18:33:39.958 [mqtt error] decode bai ExternalFlowTempDesired: ERR: invalid position
2026-03-02 18:33:44.165 [update error] unable to parse poll-read bai ExtFlowTempDesiredMin from 3108b509030d6e04 / 00: ERR: invalid position
2026-03-02 18:33:49.974 [mqtt error] decode bai ExtFlowTempDesiredMin: ERR: invalid position
2026-03-02 18:33:50.189 [update notice] sent poll-read bai FanHours QQ=31: -
2026-03-02 18:33:56.136 [update notice] sent poll-read bai FanStarts QQ=31: -
2026-03-02 18:34:02.224 [bus error] poll bai FlowTemp failed: ERR: read timeout
2026-03-02 18:34:08.191 [update notice] sent poll-read bai FlowTempDesired QQ=31: 25.00
2026-03-02 18:34:14.150 [update notice] sent poll-read bai FlowTempMax QQ=31: 0.00
2026-03-02 18:34:20.164 [update notice] sent poll-read bai HcHours QQ=31: 0
2026-03-02 18:34:25.103 [main error] scan config 05: ERR: read timeout
2026-03-02 18:34:26.210 [update error] unable to parse poll-read bai HcPumpMode from 3108b509030d4904 / 00: ERR: invalid position
2026-03-02 18:34:27.105 [main notice] scan completed 2 time(s), check again
2026-03-02 18:34:27.111 [mqtt error] decode bai HcPumpMode: ERR: invalid position
2026-03-02 18:34:32.184 [update notice] sent poll-read bai HcPumpStarts QQ=31: -
2026-03-02 18:34:38.175 [update notice] sent poll-read bai HcStarts QQ=31: 0
2026-03-02 18:34:44.170 [update notice] sent poll-read bai HcUnderHundredStarts QQ=31: 0
2026-03-02 18:34:47.231 [device notice] extra info: ID ccba97f8e604480200
2026-03-02 18:34:47.331 [main notice] update check: OK, device firmware 1[6301] available, broadcast.csv: different version available, memory.csv: different version available, vaillant/08.bai.csv: different version available, vaillant/bai.308523.inc: different version available, vaillant/broadcast.csv: different version available, vaillant/general.csv: different version available, vaillant/scan.csv: different version available
2026-03-02 18:34:50.191 [update error] unable to parse poll-read bai HoursTillService from 3108b509030d2004 / 00: ERR: invalid position
2026-03-02 18:34:52.345 [mqtt error] decode bai HoursTillService: ERR: invalid position
2026-03-02 18:34:56.156 [update notice] sent poll-read bai HwcHours QQ=31: 0
2026-03-02 18:35:00.357 [update notice] sent update-write bai SetModeOverride QQ=31: off;25.0;0.0;0;0;0;0;0;0;1
2026-03-02 18:35:00.357 [mqtt notice] write bai SetModeOverride: 1;25.0;0;0;0;0;0;0;0;1;0;0
2026-03-02 18:35:02.180 [update error] unable to parse poll-read bai HwcPostrunTime from 3108b509030d1104 / 00: ERR: invalid position
2026-03-02 18:35:07.370 [mqtt error] decode bai HwcPostrunTime: ERR: invalid position
2026-03-02 18:35:08.164 [update notice] sent poll-read bai HwcStarts QQ=31: 0
2026-03-02 18:35:14.847 [bus error] poll bai HwcTemp failed: ERR: read timeout
2026-03-02 18:35:20.158 [update notice] sent poll-read bai HwcTempDesired QQ=31: 15.00
2026-03-02 18:35:26.171 [update error] unable to parse poll-read bai HwcTempMax from 3108b509030d4304 / 00: ERR: invalid position
2026-03-02 18:35:27.417 [mqtt error] decode bai HwcTempMax: ERR: invalid position
2026-03-02 18:35:32.163 [update notice] sent poll-read bai HwcUnderHundredStarts QQ=31: 0
2026-03-02 18:35:37.721 [main error] scan config 05: ERR: read timeout
2026-03-02 18:35:38.252 [update notice] sent poll-read bai HwcWaterflow QQ=31: 0.00
2026-03-02 18:35:39.722 [main notice] scan completed 3 time(s), check again
2026-03-02 18:35:44.164 [update notice] sent poll-read bai HwcWaterflowMax QQ=31: 0.00
2026-03-02 18:35:50.174 [update notice] sent poll-read bai Maintenancedata_HwcTempMax QQ=31: 0.00
2026-03-02 18:35:56.181 [update notice] sent poll-read bai OutdoorstempSensor QQ=31: -60.44;cutoff
2026-03-02 18:36:02.205 [update notice] sent poll-read bai PowerValue QQ=31: 11 02 64 0e 64 0e
2026-03-02 18:36:08.174 [update notice] sent poll-read bai PrVortexFlowSensorValue QQ=31: -1
2026-03-02 18:36:14.185 [update notice] sent poll-read bai PumpHours QQ=31: -
2026-03-02 18:36:20.147 [update notice] sent poll-read bai PumpPower QQ=31: 0
2026-03-02 18:36:26.143 [update notice] sent poll-read bai PumpPowerDesired QQ=31: auto
2026-03-02 18:36:32.194 [update notice] sent poll-read bai ReturnTemp QQ=31: 0.00;-;ok
2026-03-02 18:36:38.185 [update notice] sent poll-read bai ReturnTempMax QQ=31: 0.00
2026-03-02 18:36:44.155 [update error] unable to parse poll-read bai SecondPumpMode from 3108b509030d0b04 / 00: ERR: invalid position
2026-03-02 18:36:49.914 [main error] scan config 05: ERR: read timeout
2026-03-02 18:36:49.915 [mqtt error] decode bai SecondPumpMode: ERR: invalid position
2026-03-02 18:36:50.459 [update notice] sent poll-read bai SHEMaxFlowTemp QQ=31: -0.06
2026-03-02 18:36:51.916 [main notice] scan completed 4 time(s), check again
2026-03-02 18:36:56.166 [update notice] sent poll-read bai Statenumber QQ=31: 31
2026-03-02 18:37:02.170 [update notice] sent poll-read bai Status01 QQ=31: 18.0;0.0;-;0.0;-;off
2026-03-02 18:37:08.196 [update notice] sent poll-read bai Status02 QQ=31: auto;50;80.0;70;70.0
2026-03-02 18:37:14.140 [update error] unable to parse poll-read bai Status16 from 3108b5040116 / 00: ERR: invalid position
2026-03-02 18:37:17.010 [mqtt error] decode bai Status16: ERR: invalid position
2026-03-02 18:37:20.177 [update error] unable to parse poll-read bai Status from 3108b5110103 / 00: ERR: invalid position
2026-03-02 18:37:22.017 [mqtt error] decode bai Status: ERR: invalid position
2026-03-02 18:37:26.174 [update notice] sent poll-read bai StorageLoadPumpHours QQ=31: -
2026-03-02 18:37:32.157 [update notice] sent poll-read bai StorageloadPumpStarts QQ=31: -
2026-03-02 18:37:38.188 [update notice] sent poll-read bai StorageTemp QQ=31: -14.94;cutoff
2026-03-02 18:37:44.155 [update notice] sent poll-read bai StorageTempDesired QQ=31: 15.00
2026-03-02 18:37:50.161 [update notice] sent poll-read bai StorageTempMax QQ=31: 0.00
2026-03-02 18:37:56.173 [update notice] sent poll-read bai TempDiffBlock QQ=31: 0
2026-03-02 18:38:02.104 [main error] scan config 05: ERR: read timeout
2026-03-02 18:38:02.653 [update notice] sent poll-read bai TempDiffFailure QQ=31: 0
2026-03-02 18:38:04.106 [main notice] scan completed 5 time(s), check again
2026-03-02 18:38:08.175 [update notice] sent poll-read bai TempGradientFailure QQ=31: 0
2026-03-02 18:38:14.174 [update notice] sent poll-read bai Templimiter QQ=31: off
2026-03-02 18:38:20.177 [update notice] sent poll-read bai TemplimiterWithNTC QQ=31: no
2026-03-02 18:38:26.183 [update notice] sent poll-read bai TempMaxDiffExtTFT QQ=31: -0.06
2026-03-02 18:38:32.630 [update error] unable to parse poll-read bai ValveMode from 3108b509030d2a04 / 00: ERR: invalid position
2026-03-02 18:38:34.153 [mqtt error] decode bai ValveMode: ERR: invalid position
2026-03-02 18:38:38.155 [update notice] sent poll-read bai ValveStarts QQ=31: -
2026-03-02 18:38:44.153 [update error] unable to parse poll-read bai VortexFlowSensor from 3108b509030dd500 / 00: ERR: invalid position
2026-03-02 18:38:49.175 [mqtt error] decode bai VortexFlowSensor: ERR: invalid position
2026-03-02 18:38:50.146 [update notice] sent poll-read bai WaterHcFlowMax QQ=31: -
2026-03-02 18:38:56.159 [update notice] sent poll-read bai WaterPressure QQ=31: 1.479;ok
2026-03-02 18:39:02.167 [update notice] sent poll-read bai WaterpressureBranchControlOff QQ=31: on
2026-03-02 18:39:08.174 [update notice] sent poll-read bai WaterpressureMeasureCounter QQ=31: -
2026-03-02 18:39:14.190 [update notice] sent poll-read bai WaterpressureVariantSum QQ=31: -
2026-03-02 18:39:14.361 [main error] scan config 05: ERR: read timeout
2026-03-02 18:39:16.363 [main notice] scan completed 6 time(s), end
2026-03-02 18:39:20.153 [update error] unable to parse poll-read bai WPPostrunTime from 3108b509030df703 / 00: ERR: invalid position
2026-03-02 18:39:21.371 [mqtt error] decode bai WPPostrunTime: ERR: invalid position
2026-03-02 18:39:26.151 [update notice] sent poll-read bai CounterStartattempts1 QQ=31: 0
2026-03-02 18:39:32.185 [update notice] sent poll-read bai CounterStartattempts2 QQ=31: 0
2026-03-02 18:39:38.134 [update notice] sent poll-read bai CounterStartAttempts3 QQ=31: 0
2026-03-02 18:39:44.176 [update notice] sent poll-read bai CounterStartAttempts4 QQ=31: 0
2026-03-02 18:39:50.174 [update notice] sent poll-read bai DcfState QQ=31: nosignal
2026-03-02 18:39:56.173 [update notice] sent poll-read bai DeactivationsTemplimiter QQ=31: 0
2026-03-02 18:40:00.366 [update notice] sent update-write bai SetModeOverride QQ=31: off;25.0;0.0;0;0;0;0;0;0;1
2026-03-02 18:40:00.366 [mqtt notice] write bai SetModeOverride: 1;25.0;0;0;0;0;0;0;0;1;0;0
2026-03-02 18:40:02.164 [update notice] sent poll-read bai DisplayMode QQ=31: 2
2026-03-02 18:40:08.184 [update notice] sent poll-read bai Expertlevel_ReturnTemp QQ=31: -1.81;cutoff
2026-03-02 18:40:14.186 [update error] unable to parse poll-read bai ExternalFlowTempDesired from 3108b509030d2500 / 00: ERR: invalid position
2026-03-02 18:40:16.439 [mqtt error] decode bai ExternalFlowTempDesired: ERR: invalid position
2026-03-02 18:40:20.158 [update error] unable to parse poll-read bai ExtFlowTempDesiredMin from 3108b509030d6e04 / 00: ERR: invalid position
2026-03-02 18:40:21.446 [mqtt error] decode bai ExtFlowTempDesiredMin: ERR: invalid position
2026-03-02 18:40:26.174 [update notice] sent poll-read bai FanHours QQ=31: -
2026-03-02 18:40:32.154 [update notice] sent poll-read bai FanStarts QQ=31: -

[aavdberg]

@john30 can you help with this, also removed als lines from the files that I use local but still see then in the log and giving error:

08.bai.csv:

type,circuit,level,name,comment,qq,zz,pbsb,id,*name,part,type,divisor/values,unit,comment
*r,
*w,
*uw,
*[Scan_id_product],Scan,,id,,product
*[id_hw],scan,,,,HW
r,,,Currenterror,Current errors,,,b503,0001,error,,UIN,,,error number,error_1,,UIN,,,error number,error_2,,UIN,,,error number,error_3,,UIN,,,error number,error_4,,UIN,,,error number
r,,,Errorhistory,Error_History,,,b503,0101,index,m,UCH,,,,status,,UCH,,,Status,time,,VTM,,,time,date,,HDA:3,,,date,error,,UIN,,,error number
w,,install,Clearerrorhistory,Clear error history,,,b503,0201,cleared,s,UCH,0=no;1=yes,,
r,,,DateTime,date/time,,,b504,00,dcfstate,,UCH,0=nosignal;1=ok;2=sync;3=valid,,DCF receiver state,btime,,BTI,,,time,bdate,,BDA,,,date,temp,,D2B,,°C,temperature
uw,,,SetModeOverride,Operation mode,,,b510,00,hcmode,,UCH,0=auto;1=off;2=heat;3=water,,boiler mode,flowtempdesired,,D1C,,°C,temperature,hwctempdesired,,D1C,,°C,temperature,hwcflowtempdesired,,UCH,,°C,temperature,ign,,IGN:1,,,,disablehc,,BI0,,,,disablehwctapping,,BI1,,,,disablehwcload,,BI2,,,,ign_1,,IGN:1,,,,remotecontrolhcpump,,BI0,,,,releasebackup,,BI1,,,,releasecooling,,BI2,,,
w,,install,SetModeOverride,Operation mode,,,b510,00,hcmode,,UCH,0=auto;1=off;2=heat;3=water,,boiler mode,flowtempdesired,,D1C,,°C,temperature,hwctempdesired,,D1C,,°C,temperature,hwcflowtempdesired,,UCH,,°C,temperature,ign,,IGN:1,,,,disablehc,,BI0,,,,disablehwctapping,,BI1,,,,disablehwcload,,BI2,,,,ign_1,,IGN:1,,,,remotecontrolhcpump,,BI0,,,,releasebackup,,BI1,,,,releasecooling,,BI2,,,
r,,,Status01,FlowTemp/ReturnTemp/OutdoorTemp/DHWTemp/StorageTemp/PumpStatus,,,b511,01,flowtemp,,D1C,,°C,temperature,returntemp,,D1C,,°C,temperature,outdoortemp,,D2B,,°C,temperature,hwctemp,,D1C,,°C,temperature,storagetemp,,D1C,,°C,temperature,pumpstate,,UCH,0=off;1=on;2=overrun;4=hwc,,pump state
r,,,Status02,HotWaterMode/Modulation/FlowTempMax/ReglerTemp/FlowTempCurrent,,,b511,02,hwcmode,,UCH,0=disabled;1=on;2=off;3=auto,,hot water mode,modulation,,UCH,,%,modulation,flowtempmax,,D1C,,°C,temperature,reglertemp,,UCH,,°C,temperature,flowtempcurrent,,D1C,,°C,temperature
uw,,,StatusCirPump,Status circulation pump,,,b512,00,value,,UCH,0=off;100=on,,
r,,,DisplayMode,Display mode of appliance,,,b509,0dda00,value,,UCH,,,
[Scan_id_product='0010023673']!load,bai.ray14.inc
!load,bai.308523.inc,,,

bai.308523.inc:

type,circuit,level,name,comment,qq,zz,pbsb,id,*name,part,type,divisor/values,unit,comment
*r,
*w,
*[id_sw],scan,,,,SW
[id_sw>=413]r,,,APCLegioProtection,d.74 APC_LegioProtection: Legionella protection for actoSTORE,,,b509,0d9704,value,,UCH,,,
[id_sw>=413]w,,install,APCLegioProtection,d.74 APC_LegioProtection: Legionella protection for actoSTORE,,,b509,0e9704,value,,UCH,,,
[id_sw>=413]r,,,APCComStatus,d.92 APC_ComStatus_DK: actoSTORE communication status,,,b509,0d6200,value,,UCH,,,
r,,,PartloadHcKW,d.00 heating partload: Heating part load,,,b509,0d0704,value,,UCH,,kW,
w,,install,PartloadHcKW,d.00 heating partload: Heating part load,,,b509,0e0704,value,,UCH,,kW,
r,,,BlockTimeHcMax,d.02 Max blocking time CH: max. burner anti cycling period at 20°C Flow temperature setpoint,,,b509,0d0904,value,,UCH,,min,minutes
w,,install,BlockTimeHcMax,d.02 Max blocking time CH: max. burner anti cycling period at 20°C Flow temperature setpoint,,,b509,0e0904,value,,UCH,,min,minutes
r,,,StorageTemp,d.04 Temp storage / she: current temperature for warm start sensor (combinations boiler only) Current storage tank sensor (system boiler only),,,b509,0d1700,temp,,D2C,,°C,temperature,sensor,,UCH,0=ok;85=circuit;170=cutoff,,sensor status
r,,,FlowTempDesired,d.05 flow/return setpoint: Flow temperature target value or return target value when return regulation is set,,,b509,0d3900,value,,D2C,,°C,temperature
r,,,StorageTempDesired,"d.07 Storage setpoint: Warm start temperature value (combination boiler plus only), Storage temperature target value (system boiler only)",,,b509,0d0400,value,,D2C,,°C,temperature
r,,,ACRoomthermostat,d.08 Room thermostat 230 V: External controls heat demand (Clamp 3-4),,,b509,0d2a00,value,,UCH,0=off;1=on,,
r,,,WP,d.10 Central heating pump: internal heating pump,,,b509,0d4400,value,,UCH,0=off;1=on,,
r,,,ExtWP,d.11 external pump: External heating pump,,,b509,0d3f00,value,,UCH,0=off;1=on,,
r,,,Storageloadpump,d.12 storage load pump: tank load pump demand,,,b509,0d9e00,value,,UCH,,%,
r,,,CirPump,d.13 Circulation pump: Hot water circulation pump (via external module),,,b509,0d7b00,value,,UCH,0=off;1=on,,
r,,,PumpPowerDesired,d.14 Desired heating pump power,,,b509,0da100,value,,UCH,0=auto;1=53;2=60;3=70;4=85;5=100,%,PWM-Desired central heating pump power
w,,install,PumpPowerDesired,d.14 Desired heating pump power,,,b509,0ea100,value,,UCH,0=auto;1=53;2=60;3=70;4=85;5=100,%,PWM-Desired central heating pump power
r,,,PumpPower,d.15 Current heating pump power: Current central heating pump power,,,b509,0d7300,value,,UCH,,,
r,,,DCRoomthermostat,d.16 room thermostat 24 V: External controls heat demand (Clamp 3'-4'),,,b509,0d0e00,value,,UCH,0=off;1=on,,
r,,,HeatingSwitch,d.23 operation mode: Wintermode active,,,b509,0df203,value,,UCH,0=off;1=on,,
r,,,StoragereleaseClock,d.25 DHW demand enabled: hot water release (tank storage) via eBus Control,,,b509,0d4704,value,,UCH,0=no;1=yes,,
r,,,PrimaryCircuitFlowrate,d.29 Primary circuit flow rate,,,b509,0dfb00,value,,UIN,100,l/min,
r,,,TargetFanSpeed,d.33 Target fan speed,,,b509,0d2400,value,,UIN,,rpm,Fan speed setpoint
r,,,FanSpeed,d.34 Actual fan speed,,,b509,0d8300,value,,UIN,,rpm,fan speed actual value
r,,,PositionValveSet,"d.35 Position TWV: Position of diverter valve; 100 = DHW, 0 = heating, 40 = middle position",,,b509,0d5400,value,,UCH,,,
r,,,FlowTemp,d.40 TFT_DK: flow temperature,,,b509,0d1800,temp,,D2C,,°C,temperature,sensor,,UCH,0=ok;85=circuit;170=cutoff,,sensor status
r,,,ReturnTemp,d.41 Temp heating return: return temperature,,,b509,0d9800,temp,,D2C,,°C,temperature,tempmirror,,UIN,,°C,,sensor,,UCH,0=ok;85=circuit;170=cutoff,,sensor status
r,,,IonisationVoltageLevel,d.44 Dig. ionisation voltage,,,b509,0da400,value,,SIN,10,,digital ionisation voltage> 80 no flame< 40 good flame
r,,,OutdoorstempSensor,d.47 Temp outside: Outside temperature (uncorrected value),,,b509,0d7600,temp,,D2C,,°C,temperature,sensor,,UCH,0=ok;85=circuit;170=cutoff,,sensor status
r,,,RemainingBoilerblocktime,d.67 Remaining burner block time: Remaining burner anti cycling time,,,b509,0d3800,value,,UCH,,min,minutes
r,,,EBusHeatcontrol,d.90 Digital control recognized: Digital regulator status,,,b509,0d0004,value,,UCH,0=no;1=yes,,
r,,,DcfState,d.91 Status DCF 77: DCF status,,,b509,0d6900,value,,UCH,0=nosignal;1=ok;2=sync;3=valid,,DCF receiver state
r,,,WaterPressure,Waterpressure: water pressure,,,b509,0d0200,press,,FLT,,bar,pressure,sensor,,UCH,0=ok;85=circuit;170=cutoff,,sensor status
r,,,ChangesDSN,Changes_DSN_DK: Numbers adjusting (storing) the DSN,,,b509,0d0c00,value,,UCH,,,
r,,,VolatileLockout,SD_VolatileLockout_DK: TRUE: STB failures is volatileFALSE: STB failure is not volataile,,,b509,0d1000,value,,UCH,240=no;15=yes,,
r,,,ModulationDesired,Modulationsetpoint_DK,,,b509,0d2e00,value,,SIN,10,%,Modulation set point
r,,,HcUnderHundredStarts,HZ_UnderHundred_SwiActi_DK: Heat switch cycles under hundred,,,b509,0d3000,value,,UCH,,,
r,,,EbusSourceOn,EbusSourceOn_DK: Activation signal of the eBus source,,,b509,0d3400,value,,UCH,0=off;1=on,,
r,,,ExternalFaultmessage,External_Faultmessage_DK: external fault message,,,b509,0d3e00,value,,UCH,0=off;1=on,,
r,,,WarmstartDemand,WarmstartDemand: aktivation of warmstart,,,b509,0d3a04,value,,UCH,0=no;1=yes,,
r,,,BoilerType,BoilerType_DK: Boiler typ of the bmu,,,b509,0d5e00,value,,UCH,,,
r,,,ParamToken,ParamToken_DK: token for parameter managment,,,b509,0d6000,value,,UCH,,,
r,,,Expertlevel_ReturnTemp,ReturnTemperature_DK: external return sensor,,,b509,0d6b00,temp,,D2C,,°C,temperature,sensor,,UCH,0=ok;85=circuit;170=cutoff,,sensor status
r,,,FloorHeatingContact,Floor heating contact,,,b509,0d7000,value,,UCH,0=off;1=on,,
r,,,Templimiter,SD_Temperaturelimiter_DK: feedback signal of the temperature limiter,,,b509,0d7700,value,,UCH,240=off;15=on,,
r,,,EbusVoltage,EbusVoltage_DK: feedback signal of the eBus source,,,b509,0d7f00,value,,UCH,0=off;1=on,,
r,,,Testbyte,Testbyte_DK: Testbyte (relevant for the Tester),,,b509,0d9900,value,,UCH,,,
r,,,DSN,DSN_DK: DSN: Device Specific number,,,b509,0d9a00,value,,UIN,,,
r,,,TargetFanSpeedOutput,TargetFan_Speed_Output_DK,,,b509,0d9f00,value,,UIN,,rpm,output fan speed
r,,,PowerValue,PowerValue,,,b509,0daa00,value,,HEX:6,,,"Power Values of the Boiler (min Power, max Power)"
r,,,Statenumber,Statenumber_DK: status number,,,b509,0dab00,value,,UCH,,,
r,,,WaterpressureBranchControlOff,WaterpressureBranchControlOff_DK: water pressure branch controll off,,,b509,0daf00,value,,UCH,0=off;1=on,,
r,,,DSNStart,DSN Start adress,,,b509,0d3104,value,,UIN,,,
r,,,ExtStorageModulCon,ExtTankModulCon_DK: external tank modul connected (VR65),,,b509,0dbf00,value,,UCH,0=no;1=yes,,
r,,,PartnumberBox,Partnumber_Box,,,b509,0dc000,value,,HEX:5,,,part number of the eBox
r,,,WPSecondStage,WP_SecondStage_DK: Second stage of the pump activated,,,b509,0ded00,value,,UCH,0=off;1=on,,
r,,,TemplimiterWithNTC,SD_STL_with_NTC: Safety temperature limit concept:1 = safety temp. Limit check with NTC0 = safety temp. Limit check with contact,,,b509,0dd200,value,,UCH,240=no;15=yes,,
r,,,VolatileLockoutIFCGV,SD_VolatileLockout_IFC_GV_DK: all IFC faults are volataile,,,b509,0dd300,value,,UCH,240=no;15=yes,,
r,,,VortexFlowSensor,"VortexFlowSensor_DK: Predictive Maintenance data, CH water flow",,,b509,0dd500,value,,UIN,,,
r,,,DisplayMode,DisplayMode_DK: Display mode of the aplliance,,,b509,0dda00,value,,UCH,,,
r,,,InitialisationEEPROM,InitialisationEEPROM: Initialisation off all EEPROM values (done in the production),,,b509,0ddc00,value,,UCH,0=no;1=yes,,
r,,,TimerInputHc,TimerInputCH_DK: timer input (block heatdemand),,,b509,0dde00,value,,UCH,0=off;1=on,,
r,,,FanMinSpeedOperation,FanMinSpeedOperation,,,b509,0ddf00,value,,UIN,,rpm,Minimum Fan speed of the appliance
r,,,FanMaxSpeedOperation,FanMaxSpeedOperation,,,b509,0de000,value,,UIN,,rpm,Maximum Fan speed of the appliance
r,,,DCFTimeDate,DCF_TimeDate_DK,,,b509,0de500,btime,,BTI,,,time,bdate,,BDA,,,date
r,,,FlowSetPotmeter,FlowSetPotmeter: flow setpoint potentiometer,,,b509,0df003,value,,D2C,,°C,temperature
r,,,ProductionByte,ProductionByte,,,b509,0d3e04,value,,UCH,,,
r,,,SerialNumber,SerialNumber,,,b509,0d3f04,value,,HEX:8,,,serial number of AI
r,,,ReturnRegulation,d.17 Return regulation: heating flow/return regulation activation,,,b509,0d0c04,value,,UCH,0=off;1=on,,
w,,install,ReturnRegulation,d.17 Return regulation: heating flow/return regulation activation,,,b509,0e0c04,value,,UCH,0=off;1=on,,
r,,,SecondPumpMode,"d.19 Mode of 2 speed pump: Operating mode of the two-stage heating pump0: burner mode = 2, pre/post-run = 1; 1: CH + post-run = 1, DHW = 2, 2: as 1 but rotation speed in CH is dependent of heating part load, (defaultsetting)3: always stage 2",,,b509,0d0b04,value,,UCH,,,
w,,install,SecondPumpMode,"d.19 Mode of 2 speed pump: Operating mode of the two-stage heating pump0: burner mode = 2, pre/post-run = 1; 1: CH + post-run = 1, DHW = 2, 2: as 1 but rotation speed in CH is dependent of heating part load, (defaultsetting)3: always stage 2",,,b509,0e0b04,value,,UCH,,,
r,,,AccessoriesOne,d.27 Option relais 1,,,b509,0d4b04,value,,UCH,1=circulationpump;2=extheatingpump;3=storagechargingpump;4=fluegasflapextractorhood;5=externalgasvalve;6=externalerrormessage;7=solarpump;8=remotecontrol,,Accesory relay 1 function
w,,install,AccessoriesOne,d.27 Option relais 1,,,b509,0e4b04,value,,UCH,1=circulationpump;2=extheatingpump;3=storagechargingpump;4=fluegasflapextractorhood;5=externalgasvalve;6=externalerrormessage;7=solarpump;8=remotecontrol,,Accesory relay 1 function
r,,,AccessoriesTwo,d.28 Option relais 2,,,b509,0d4c04,value,,UCH,1=circulationpump;2=extheatingpump;3=storagechargingpump;4=fluegasflapextractorhood;5=externalgasvalve;6=externalerrormessage;7=solarpump;8=remotecontrol,,Accesory relay 2 function
w,,install,AccessoriesTwo,d.28 Option relais 2,,,b509,0e4c04,value,,UCH,1=circulationpump;2=extheatingpump;3=storagechargingpump;4=fluegasflapextractorhood;5=externalgasvalve;6=externalerrormessage;7=solarpump;8=remotecontrol,,Accesory relay 2 function
r,,,FanSpeedOffsetMin,d.50 MinFanSpeedOffset,,,b509,0d2404,value,,SIN,,rpm,Offset for minimum fan speed
w,,install,FanSpeedOffsetMin,d.50 MinFanSpeedOffset,,,b509,0e2404,value,,SIN,,rpm,Offset for minimum fan speed
r,,,FanSpeedOffsetMax,d.51 MaxFanSpeedOffset,,,b509,0d2504,value,,SIN,,rpm,Offset for maximum fan speed
w,,install,FanSpeedOffsetMax,d.51 MaxFanSpeedOffset,,,b509,0e2504,value,,SIN,,rpm,Offset for maximum fan speed
r,,,SolPostHeat,d.58 solar function: special DHW functions0: solar function deactivated (default)1: solar function activated and DHW setpoint minimum 60°C2: solar function activated and DHW setpoint like combi standard (min 35°)3: DHW setpoint minimum 60°C (poti),,,b509,0d7304,value,,UCH,,,
w,,install,SolPostHeat,d.58 solar function: special DHW functions0: solar function deactivated (default)1: solar function activated and DHW setpoint minimum 60°C2: solar function activated and DHW setpoint like combi standard (min 35°)3: DHW setpoint minimum 60°C (poti),,,b509,0e7304,value,,UCH,,,
r,,,DeactivationsTemplimiter,d.60 Number STL cut off: Number of safety temperature limiter cut offs,,,b509,0d2000,value,,UCH,,,
r,,,DeactivationsIFC,"d.61 Number ignition device cut off: number of lock outs (unsuccessfull ignitons in the last attempt, flame failure)",,,b509,0d1f00,value,,UCH,,,
r,,,AverageIgnitiontime,d.64 average ignition time,,,b509,0d2d00,value,,UCH,10,s,average ignition time
r,,,CounterStartattempts1,d.68 ignition attempts 1: unsuccessfull ignitions in the first attempt,,,b509,0d6e00,value,,UCH,,°C,temperature
r,,,CounterStartattempts2,d.69 ignition attempts 2: unsuccessfull ignitions in the second attempt,,,b509,0d6f00,value,,UCH,,°C,temperature
r,,,FlowsetHcMax,d.71 Max value flow temp: Adjustment of maximum central heating setpoint range (maximum endposition of potmeter),,,b509,0d0e04,value,,D2C,,°C,temperature
w,,install,FlowsetHcMax,d.71 Max value flow temp: Adjustment of maximum central heating setpoint range (maximum endposition of potmeter),,,b509,0e0e04,value,,D2C,,°C,temperature
r,,,WarmstartOffset,d.73 Warmstart offset: Offset for warm start target value (combination boilers only),,,b509,0d1004,value,,D2C,,°C,temperature
w,,install,WarmstartOffset,d.73 Warmstart offset: Offset for warm start target value (combination boilers only),,,b509,0e1004,value,,D2C,,°C,temperature
r,,,StorageLoadTimeMax,d.75 Max load time storage: Maximum charging time for a storage without own control,,,b509,0d1204,value,,UCH,,min,minutes
w,,install,StorageLoadTimeMax,d.75 Max load time storage: Maximum charging time for a storage without own control,,,b509,0e1204,value,,UCH,,min,minutes
r,,,HcHours,d.80 operating hours CH: central heating operation hours,,,b509,0d2800,value,,UIN,,h,hours
r,,,HcStarts,d.82 Burner starts heating,,,b509,0d2900,value,,UIN,-100,,cycles in heating mode
r,,,DSNOffset,d.93 Device specific number: DSN aplliance variant setting,,,b509,0d3004,value,,UCH,,,
w,,service,DSNOffset,d.93 Device specific number: DSN aplliance variant setting,,,b509,0e3004,value,,UCH,,,
r,,,SetFactoryValues,d.96 Set factory settings,,,b509,0d6804,value,,UCH,0=no;1=yes,,
w,,install,SetFactoryValues,d.96 Set factory settings,,,b509,0e6804,value,,UCH,0=no;1=yes,,
r,,,TempGradientFailure,TempGradientFailure_DK: Number of cut offs of the boilers cause of to high gradient (S.54),,,b509,0d1100,value,,UCH,,°C,temperature
r,,,TempDiffBlock,TempDiffBlock_DK: Number of modulationblocking of the boilers cause of to high/incorrect difference of flow/return temperatures,,,b509,0d1200,value,,UCH,,°C,temperature
r,,,TempDiffFailure,TempDiffFailure_DK: Number of cut offs of the boilers cause of to high/incorrect differences of flow/return temperatures,,,b509,0d1300,value,,UCH,,°C,temperature
r,,,PumpHours,Pump operation hours,,,b509,0d1400,value,,UIN,,h,hours
r,,,HcPumpStarts,CH_PumpCommunt_DK: pump switchings,,,b509,0d1500,value,,UIN,,,start count
r,,,OverflowCounter,OverflowCounter_DK: Predictive Maintenance counter have got an overflow,,,b509,0d1e00,value,,UCH,0=no;1=yes,,
r,,,TempMaxDiffExtTFT,MaxTempDiffExtTFT_DK: Predictive maintenance data,,,b509,0d2700,value,,D2C,,°C,temperature
r,,,StorageTempMax,Temp storage max: maximum temperature measured by the external tank sensor,,,b509,0d3600,value,,D2C,,°C,temperature
r,,,FlowTempMax,TFT_max_DK: maximum temperature measured by the flow sensor,,,b509,0d3700,value,,D2C,,°C,temperature
r,,,FanPWMSum,Fan_PWM_Sum_DK: Predictive Maintenance data for the fan damage recognition,,,b509,0d3a00,value,,UIN,,,
r,,,FanPWMTest,Fan_PWM_Test_DK: Predictive Maintenance data for the fan damage recognition,,,b509,0d3b00,value,,UCH,,,
r,,,DeltaFlowReturnMax,MaxDeltaFlowReturn_DK: Predictive Maintenance data,,,b509,0d3d00,value,,D2C,,°C,temperature
r,,,StorageLoadPumpHours,TankLoadPumpOperationHours_DK: Preditive maintenance data,,,b509,0d4c00,value,,UIN,,h,hours
r,,,StorageloadPumpStarts,TankloadPumpCommunt_DK: Preditive maintenance data,,,b509,0d4f00,value,,UIN,,,start count
r,,,CounterStartAttempts3,CounterStartAttempts3_DK: unsuccessfull ignitions in the third attempt,,,b509,0d8100,value,,UCH,,°C,temperature
r,,,CounterStartAttempts4,CounterStartAttempts4_DK: unsuccessfull ignitions in the fourth attempt,,,b509,0d8200,value,,UCH,,°C,temperature
r,,,ReturnTempMax,TRT_max_DK: max. return temperature,,,b509,0dbe00,value,,D2C,,°C,temperature
r,,,SHEMaxFlowTemp,SHE_MaxFlowTemp_DK: maximum flow temperature DHW,,,b509,0dc300,value,,D2C,,°C,temperature
r,,,WaterHcFlowMax,MaxWaterFlowCH_DK: Predictive Maintenance data,,,b509,0dd000,value,,UIN,,,
r,,,WaterpressureVariantSum,WaterpressureVariantSum_DK: Predictive Maintenance data,,,b509,0df000,value,,UIN,,mbar,pressure
r,,,WaterpressureMeasureCounter,WaterpressureMeasureCounter_DK: Predictive Maintenance data,,,b509,0df100,value,,UCH,,,
r,,,PrAPSCounter,PrAPSCounter_DK: Predictive Maintenance data,,,b509,0df200,value,,UCH,,,
r,,,PrAPSSum,PrAPSSum_DK: Predictive Maintenance data,,,b509,0df300,value,,UIN,,s,seconds
r,,,PrEnergySumHc1,PrEnergySumCH1_DK: Predictive Maintenance data,,,b509,0df500,value,,ULG,,,
w,,install,PrEnergySumHc1,PrEnergySumCH1_DK: Predictive Maintenance data,,,b509,0ef500,value,,ULG,,,
r,,,PrEnergyCountHc1,PrEnergyCountCH1_DK: Predictive Maintenance data,,,b509,0df600,value,,ULG,,,
w,,install,PrEnergyCountHc1,PrEnergyCountCH1_DK: Predictive Maintenance data,,,b509,0ef600,value,,ULG,,,
r,,,PrEnergySumHc2,PrEnergySumCH2_DK: Predictive Maintenance data,,,b509,0df700,value,,ULG,,,
w,,install,PrEnergySumHc2,PrEnergySumCH2_DK: Predictive Maintenance data,,,b509,0ef700,value,,ULG,,,
r,,,PrEnergyCountHc2,PrEnergyCountCH2_DK: Predictive Maintenance data,,,b509,0df800,value,,ULG,,,
w,,install,PrEnergyCountHc2,PrEnergyCountCH2_DK: Predictive Maintenance data,,,b509,0ef800,value,,ULG,,,
r,,,PrEnergySumHc3,PrEnergySumCH3_DK: Predictive Maintenance data,,,b509,0df900,value,,ULG,,,
w,,install,PrEnergySumHc3,PrEnergySumCH3_DK: Predictive Maintenance data,,,b509,0ef900,value,,ULG,,,
r,,,PrEnergyCountHc3,PrEnergyCountCH3_DK: Predictive Maintenance data,,,b509,0dfa00,value,,ULG,,,
w,,install,PrEnergyCountHc3,PrEnergyCountCH3_DK: Predictive Maintenance data,,,b509,0efa00,value,,ULG,,,

bai.ray14.inc:

type,circuit,level,name,comment,qq,zz,pbsb,id,*name,part,type,divisor/values,unit,comment
*r,
*w,
r,bai,,FlowTempDesired,Flow/return setpoint,,,b509,0d3900,value,,D2C,,°C,temperature
r,bai,,PumpPower,Current heating pump power,,,b509,0d7300,value,,UCH,,%,current CH pump power
r,bai,,PumpPowerDesired,Desired heating pump power,,,b509,0da100,value,,UCH,0=auto;1=53;2=60;3=70;4=85;5=100,%,PWM desired
w,bai,install,PumpPowerDesired,Desired heating pump power,,,b509,0ea100,value,,UCH,0=auto;1=53;2=60;3=70;4=85;5=100,%,PWM desired
r,bai,,TimerInputHc,Timer input block heat demand,,,b509,0dde00,value,,UCH,0=off;1=on,,

[verkel21]

Same problem here with a Wolf CWL-300

[07:06:39] INFO: �[32meBUSd addon version 26.1.6�[0m
[07:06:39] INFO: �[32mebusd --foreground --updatecheck=off --mqtthost=core-mosquitto --mqttport=1883 --mqttuser= --mqttpass= --mqttjson --mqttint=/config/mqtt-hassio.cfg --device=/dev/serial/by-id/usb-Silicon_Labs_CP2102_USB_to_UART_Bridge_Controller_0001-if00-port0 --mqttjson --configpath=/config/ --pollinterval=1 �[0m
2026-03-24 07:06:39.939 [device notice] transport opened
2026-03-24 07:06:39.942 [main notice] ebusd 26.1.26.1 started on device: /dev/serial/by-id/usb-Silicon_Labs_CP2102_USB_to_UART_Bridge_Controller_0001-if00-port0, serial
2026-03-24 07:06:39.943 [bus notice] bus started with own address 31/36
2026-03-24 07:06:39.968 [bus notice] signal acquired
2026-03-24 07:06:40.024 [mqtt notice] connection established
2026-03-24 07:06:40.074 [bus notice] new master 37, master count 2
2026-03-24 07:06:40.075 [update notice] sent poll-read excellent SettingInletFlow QQ=31: 55
2026-03-24 07:06:41.129 [update notice] sent poll-read excellent SettingExhaustFlow QQ=31: 50
2026-03-24 07:06:43.141 [update notice] sent poll-read excellent InletFlow QQ=31: 56
2026-03-24 07:06:45.112 [update notice] sent poll-read excellent ExhaustFlow QQ=31: 47
2026-03-24 07:06:47.115 [update notice] sent poll-read excellent InletFanSpeed QQ=31: 732
2026-03-24 07:06:49.119 [update notice] sent poll-read excellent ExhaustFanSpeed QQ=31: 678
2026-03-24 07:06:49.943 [main notice] found messages: 10 (0 conditional on 0 conditions, 10 poll, 0 update)
2026-03-24 07:06:51.119 [update notice] sent poll-read excellent PerilexPosition QQ=31: 1
2026-03-24 07:06:53.144 [update notice] sent poll-read excellent Stufenschalter QQ=31: 1
2026-03-24 07:06:55.110 [update notice] sent poll-read excellent Aussentemperatur QQ=31: 14.4
2026-03-24 07:06:57.125 [update notice] sent poll-read excellent PressureInlet QQ=31: 31.0

[john30]

hex digits are not sent to HA discovery as this would be rather useless there. you could enable it nevertheless by adjusting the mqtt-hassio.cfg file, but the right thing to do would be to determine what the hex digits mean and then use the right data type for that.